LH201

HAND OPERATED LEVER HOIST

The Hand Operated Lever Hoist LH201 meets all safety standards and is one of the most durable mechanisms in its class. A layer of carbon coating protecting gear parts and braking system components ensures a long service life even in the most difficult conditions and at maximum operating loads.
¾-9T
Rated
Capacity
5-40FT
Standard
Lift
M4
Mechanical
Class

BRAKE SYSTEM

Hitchlifting company is certain about the highest quality of brake mechanism construction of HITCH Professional and provides lifetime warranty for it. Please consult «Service» section for the details on lifetime warranty. HITCH brake discs of HITCH Professional are less breakable. If brake discs on HITCH Professional hoist are worn out within three years after purchase, we replace them for free.
¾ - 9T

dimensions (in)

capacity (t)ABCDH (HEADROOM)LK
3/45-11/163-3/85-1/41-7/1613-3/811-1/415/16
15-11/163-3/85-1/41-7/1613-3/811-1/415/16
1-1/26-7/845-7/81-3/41516-1/81-3/16
26-7/845-7/81-3/41516-1/81-3/16
37-11/164-1/27-1/2219-5/1616-1/81-5/16
67-11/164-1/29-1/22-9/1624-7/1616-1/81-7/8
97-11/164-1/2123-3/1627-9/1616-1/82-1/8


specification

Stock Number**Rated Capacity (t)test load (t)Standard Lift (Ft)***Pull to Rated Load (Lbs)Number of Load Chain FallsLoad Chain dia. Strength Class G80 (mm)Net Weight (Lbs)Weight for additional 3,3 ft of lift (Lbs)
1227513/41-1/8531-1/216211-3/4
12201111-1/2531-1/216211-3/4
1221511-1/22-1/4549-7/161825-3/83
12202123549-7/161825-3/83
12203134-1/257211040-13/164-7/8
12206167-1/2576-7/1621060-5/89-11/16
122091911-1/4581310101-7/1614-9/16


*Options:
«G» – «Galvanic» – Load chain with the galvanic coating
«B» – «Bearings» – Hoist equipped with the friction bearings
«S» – «SMART» – Overload Protection System
«TD» – «TD» – Trolley Directly
**Stock Number is indicated for standard design and Standard Lift.
***Maximum standard lift height of 60 Ft. Required lifting height is needed to specify in the order.
Operation temperature: -40 F Up to +150 F
Necessary to check the brake at a temperature below 32 F in case of freezing
Operation humidity - 100%



Advantages and characteristics

Currently, you can buy Hand Operated Lever Hoists LH201 with capacities of 3/4, 1, 1-1/2, 2, 3, 6, and 9 tons to perform any tasks.
 

Compact design and mobility

HITCH hoisting equipment can move easily from place to place due to its compact design. Even where space is limited, the equipment is convenient to use.
 

Long service life and high performance capability

The HITCH hoists by Series Professional are highly professional pieces of equipment, the service life of which in any situation and under heavy loads exceeds the service life of other equipment with the same functionality. This advantage is provided by the application of carbon coating technology.
This carbon coating is applied to the gears and the braking system components of the Lever Hoists HITCH in an extremely thin layer, thus ensuring the components have higher strength than steel without the coating. At the same time, the coating reduces friction and wear and tear, which is also important for the durability of the equipment. This has a positive effect on productivity, reducing the possibility of scuffing and pitting, and the level of noise of the hoist. Combined, the Hand Operated Lever Hoist HITCH has a low coefficient of friction and high wear resistance, characteristics which are confirmed with the offer of a five year warranty* (optional).


The reactions and materials that reduce the friction of the hoist on the operation and run "dry" are:
MoS2 - Molybdenum Sulphide
PTFE - Polytetrafluoroethylene (Teflon ®)

Friction Coefficient (t):
Steel AISI 52100 (DIN 1.3505) without coating
Coating MoS2 (Molybdenum Sulphide)
®) Coating PTFE (polytetrafluoroethylene, Teflon ®)
Coating MoS2,  deposited by physical vapor deposition

Carbon coating
X – Study is discontinued due to the strong adhesive wear
Slidepath

 

Clear marking

Each HITCH product is accompanied with a unique serial number and mechanical class marking that allows you to quickly and accurately determine the characteristics and the type of equipment.
 

Identification according to mechanical class

To simplify the determination of modes of loading, the manufacturer has developed technology for marking mechanical HITCH classes. Belonging to a specific mechanical class is indicated by different colors. The equipment used in industry to operate in conditions of high and medium loads is colored black, and corresponds to M4-M5 classes. The equipment used in industry to operate in conditions of medium and low loads is painted in green and corresponds to the M2 class.
 

Usage class of the mechanism

Class of use of the mechanism is determined by the expected total duration of operation, calculated in hours, as well as the nominal classes, shown in Table 1:

Class of use of mechanisms

Class of useTotal duration of testing, in hoursNote
T0200Irregular usage
T1400
T2800
T31 600
T43 200Regular usage in light conditions
T56 300Regular usage with interruptions
T612 500Regular intensive usage
T725 000Intensive usage
T850 000
T9100 000


Loading mode

Load Mode determines the relative duration of work with the equipment in the conditions of maximum or reduced load. Table 2 shows the nominal loading modes.
The nominal value of the load factor for the equipment is also determined in Table 2 (the actual value that is closest to the nominal ratio is significant).

Table 2.
Nominal load distribution coefficients of mechanisms Km

Loading modeNominal load distribution coefficient KmNote
L1-Light0.125Equipment is regularly operated under small loads, but rarely under the largest loads
L2- Normal0.25Equipment is regularly operated under moderate loads, and quite often under the largest loads
L3-Heavy0.50Equipment is regularly operated under high loads, and often under the largest loads
L4-Severe1.00Equipment is regularly operated under the largest loads


Definition of classification group of equipment in general

By installing the class of use and loading mode, according to Table 3 it is possible to determine the classification of a group of equipment.

Table 3
Classification group of equipment in general

Loading modeNominal load distribution coefficientKmUsage class of the mechanism
ToT1T2T3T4T5T6T7T8T9
L1-Light0.125M1M2M3M4M5M6M7M8
L2- Normal0.25M1M2M3M4M5M6M7M8
L3-Heavy0.50M1M2M3M4M5M6M7M8
L4-Severe1.00M2M3M4M5M6M7M8


High hull strength

The housing of the hoist is made of impact-resistant pressed steel, which guarantees long-lasting reliable operation of the equipment in the most difficult conditions. The housing of the hoist is protected against corrosion with a wear-resistant layer of powder paint, therefore the equipment is able to operate in harsh weather conditions.
 

Heat-treated plates

Heat treated bearing plates provide the high rigidity needed to maintain the shape of the housing and the effective operation of equipment, regardless of the load on the hoist. The process of heat treatment also prevents abrasion of material during contact time between the loaded chains and side plates.
 

Hooks/Load security

HITCH designed the hooks which are made of alloy steel. The specific advantage of this important element of the hoist is that when under excessive load, the hook is not destroyed, and is instead gradually stretched, signaling excessive weight which provides added security during lifting. The operator can therefore promptly react to the situation and prevent an accident.
The use of equipment with a hook which is damaged or has a broken safety latch is prohibited. Therefore HITCH has specifically developed cast steel thick-walled safety latches and fixed them at the base in order to increase safety. The notch on the end of the latch and on the end of the hook is engineered to engage the tip of the hook to protect against lateral impact damage.
Top and bottom hooks are fitted with a wide throat, which makes it easy to fix the load. The hooks can be rotated 360 degrees for quick and easy operation.
Option: The Shipyard hook is designed for use in selected areas of shipbuilding, as well as in sheet forming.

BRAKE SYSTEM

HITCH Professional hoists are equipped with the most safe and durable brake system in the market. The construction of brake complies with the strictest generally accepted standards.
Double pawls divide the load onto opposite sides of ratchet disc. It increases safety of operator and extends life time of the hoist.
Hitchlifting company is certain about the highest quality of brake mechanism construction of HITCH Professional and provides lifetime warranty for it. Please consult «Service» section for the details on lifetime warranty.
HITCH brake discs of HITCH Professional are less breakable. If brake discs on HITCH Professional hoist are worn out within three years after purchase, we replace them for free.
 

Loading chain

The chain calibrated and tested in the USA by Hitchlifting Inc., meets the requirements of class G80 chain strength and provides safety and a long service life of the hoist.
 

Ease of chain management

The standard mechanism of "free-wheel mode" chain is suitable for the rapid attachment of the load and the chain runs through the hoist in both directions.
 

 Smooth running of the chain

Strong guide rollers are used to prevent breakdown and seizing of the chain on the lift wheel. Shroud acts as a chain guide and protects from debris and precipitation.
 

Chain brake

The chain brake is designed in such a way that excludes the possibility of it becoming stuck in the lift wheel, which could lead to failure of the hoist. It is made from durable forged alloy steel.
 

Pinion shaft

This part is made of hardened steel of high-class durability and reliability for industrial use.
 

Ergonomic handle is rotated 360 degrees

A full handle rotation of 360 degrees allows the operator to use the most convenient grip of the hoist for maximum range of motion and, as a consequence, increase the efficiency of working with the hoist. The short lever has ribs attached to the rubber handle which provides a comfortable grip under any climatic conditions.
 

Minimum physical efforts

Thanks to its improved drive, HITCH’s short handle, compact housing, double reduction gear reducer and ergonomic design mean that it requires a minimum of effort when working with the hoist.
 

Quick technical inspection

Our equipment is completed with the use of nuts with nylon inserts that prevent spontaneous loosening and allow mechanics to quickly dismantle it for inspection and simple repairs.